Cook Group Ltd
Condensation Control Building Preservation Flood Remediation Structural Waterproofing

Mailing List
Join our Mailing List
Name
Email

Social
Click for our Facebook page Click for our Twitter page

Flood Warnings

Legends
type1 Member

Standards
Property Care
Constructionline - The commonsense solution for both sides of the tender
Contractors Health and Safety Assessment Scheme
CSCS - Construction Skills Certification Scheme
Proud members of the British Geo membrane Association

Damp proofing Treatment in Hull

What is Rising Dampness ?

Most building materials which we use for constructing walls are porous, in simple terms this means they will (or have the ability to) absorb water if they come into in contact with it.
This is because the materials are not solid, but contain many very small holes called pores and capillaries into which water can pass. As water spreads through porous materials it draws more water along behind it - even against the force of gravity - in much the same way that a kitchen towel will absorb a small spill of water if just one edge of it is dipped into the water.
This basically means that a wall in contact with wet ground will absorb water and the water will eventually pass up the walls - this is rising damp. Rising dampness is the result of capillarity, this being the process in which water rises up the very fine tubes formed by the pores. 

   Rising Damp       Rising Damp

As the water passes up the wall, it evaporates away from the surface at a rate mainly depending on the temperature and type of wall covering. Eventually the amount of water passing into the wall is balanced by the amount which can evaporate and the water does not reach any higher up the wall. This may result in a tide mark being seen across the wall - below it the wall is constantly damp, but above it is relatively dry. The height of the tide mark depends on the dampness of the ground and how quickly water can evaporate from the wall. If the wall is coated with a water resistant covering, such as tiles, gloss paint or vinyl paper, the damp may reach much higher before it can evaporate. Rising damp rarely rises above a height of 1 metre above the external ground level and / or the internal solid floor level.
Often the rising water will carry salts into the wall from the ground. These can react with plaster or brickwork and a deposit of crumbly white crystals may be seen on the surface. They can be brushed off, and may build up again, and affected plaster will eventually perish, becoming soft and falling off.
Rising damp can be most costly when timber floors are affected. In older houses floor joists are often seated directly into walls, with little or no protection from the dampness. Joists are usually supported directly on to the physical damp proof course in more modern building constructions. Where rising dampness exists, masonry, on which the timber joists are supported, becomes wet. Eventually damp wood will become infected with wood decaying fungi such as wet rot or dry rot, and may also become attacked by wood boring beetles. These cause complete breakdown of the structure of the wood and the floor may eventually collapse. This can occur over a short period, or take many years, depending on the degree and speed of development of the dampness and the resultant fungal or insect attack. 
Joists can be protected by chemical treatments and wrapping the ends in a damp-proof membrane before inserting them into a damp wall. (Even a wall which has been damp-proofed will still contain some residual moisture and it is important that new replacement timbers are also treated in this way.) Better than chemical treatments, is to ensure joist ends remain dry - but this is not always possible.

Bridging Of Damp-Proof Courses

The damp-proof course installed in a wall controls water from moving up the wall, but this is obviously useless if water can by-pass around it. When this happens this is referred to as bridging. The most common form of bridging is when the ground level outside a solid wall is higher than the installed damp-proof course. Other forms of bridging include internal plastering and external wall renders extending down over the damp-proof course line. 

Water Splash

If soil or paths are allowed to touch the wall above the level of the damp-proof course, ground water will be in contact with the wall and rising damp can occur. Exposed timbers bearing onto the wall may also be at risk from dampness and therefore may rot. Even if the ground level is below the damp-proof course bridging can occur in a solid wall when rainwater hits the ground and splashes on to the wall above the damp-proof course.
 
For this reason the ground level should be at least 150 mm below the damp-proof course (which should be below the level of any floor timbers, if at all possible). If a path or driveway is too high, the situation can be improved by digging out a channel along the wall (between 100 mm - 300 mm wide) and lining it with gravel, to act as a soak-away.
Alternatively in some instances we may be able to apply a specialist water resistant coating to the brickwork

Treating Rising Damp - Damp-Proof Courses

Old buildings were constructed with little or no protection from rising damp, but in more recent times rising damp has been prevented by inserting a layer of water-proof material into the wall as it was built. This was often slate, poured bitumen or bituminous felt, but nowadays is most likely to be a layer of PVC. Although some of these have a long life, it is possible for these substances to perish and allow water through. This is not the case in modern PVC damp-proof courses.

Luckily, it is possible to damp-proof a building without dismantling it. The main methods we use today are chemical injection, mortar injection, electro-osmosis and sometimes the insertion of physical damp-proof courses.

Chemical injection is the most suitable and cost effective method for solid brick and cavity brick walls. The other methods are necessary for thicker stone and rubble-filled walls. They may also be suitable for breeze block walls, which are difficult to treat because of their open structure and brittle nature when drilled.

© Copyright Cook Group Ltd   

Image contact-cook-group.gif

Sub Categories
Sub Categories within Damp proofing Treatment in Hull category

Chemical Injection
Chemical Injection
This section describes how rising damp is controlled by the installation of a liquid or cream based injection system
Mortar Injection
Mortar Injection
This section describes how we control rising damp in very thick or random stone walls using Injection Mortar systems
Replastering After a DPC installation
Replastering After a DPC installation
Information on why you should have replastering works carried after damproofing treatments
Electrosmosis
This section tells you how we control rising damp using the electrosmotic dpc type systems
  

Downloads
Downloads within Damp proofing Treatment in Hull category

Rising Damp Technical Paper This is our rising damp technical paper which tells you a bit about rising damp and how we treat it.


Todays Featured Images
Todays featured Gallery Images

Another patch of stone
Another section of chalk wall awaiting rebuilding
Another patch of stone

2
Another shot of the problem
2


Cookies
This site uses Cookies. Info on Cookies. By continuing to browse this site you are agreeing to our use of cookies.


Home Page    Member Area    Bookmark Page    Email a Friend    Search    A to Z   

Site Map    Terms    Privacy    Feedback Form